Glowshift 2" Tachometer Gauge Manuel d'utilisateur télécharger pdf

Tinted Series Tachometer

For Product Numbers: GS-T10

Wire Harness Color Code

Red:

12v Ignition Source (+) (switched)

Orange:

12v Switched Headlamp Source (+) (optional)

Black:

Vehicle Ground ( - )

Green:

Connects to Vehicle’s Tachometer Signal Wire

1. Disconnect the negative battery cable.

Connecting the Power Wire Harness

2. Connect the green wire to the vehicle’s tachometer signal wire

or negative side of the coil. You must consult your manual to

ensure proper location. If connecting to an aftermarket ignition

system, be sure to follow the manufacturer’s instructions for

connecting a tachometer. Please consult a service manual or

mechanic before installing.

 Tachometer Test Wire: Some vehicles may have a

tachometer test wire to obtain a tachometer signal from.

Consult your repair manual or licensed mechanic to

confirm the location of this wire.

 Tachometer Adapter: It may be necessary to install a

Tachometer Adapter if you have a multiple coil system.

You can purchase a Tachometer Adapter from local auto

parts store.

 Tachometer Filter: It may be necessary to use a

Tachometer Filter if you vehicle has either a points style

or HEI ignition system. You can purchase a Tachometer

Filter from www.GlowShift.com

 Note: Be sure to use a grommet when routing wires

through the firewall to protect them from stripping and

damage.

3. Using automotive grade wiring (18 gauge); connect the red

wire to a positive 12 volt ignition (switched) source. It may be

connected to the fuse panel, an accessory wire, or any positive 12

volt source that turns on and off with the ignition.

4. Using automotive grade wiring (18 gauge); connect the black

wire to any good (unpainted) ground connection. You may also

route a wire directly to the negative side of the vehicle’s battery.

5. The Night Time Dimming feature decreases the brightness of the

gauge face by 30%. Connect the orange wire to the 12 volt positive

headlamp source. This allows the mode to be activated when the

headlights come on. This step is optional and will not affect operation

of the gauge if it is omitted.

 Note: Do not connect the orange wire to a dimmer wheel.

This will cause the gauge lighting to flicker.

6. Use the Cylinder Selection Switch on the back of the gauge to set

the number of engine cylinders on the tachometer to match that of your

vehicle. Do this before applying power to the gauge.

 If you need to change the cylinder selection, you must remove

power from the gauge, make your selection, and then reapply

power to the gauge for proper calibration.

Switch # Cylinders

0 10

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 9

7. Reconnect the negative battery cable.

1 2

Tinted Series Tachometer 1

Résumé du contenu

Page 1 - Tinted Series Tachometer

Tinted Series Tachometer For Product Numbers: GS-T10 Wire Harness Color Code Red: 12v Ignition Source (+) (switched) Orange: 12v Switched Headlamp

Page 2

Additional Installation Information & Material Requirements  GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauge

Commentaires sur ces manuels

Pas de commentaire

Glowshift 2" Tachometer Gauge Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Glowshift 2" Tachometer Gauge. GlowShift 2" Tachometer Gauge User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Glowshift 2" Tachometer Gauge